How to Replace a kia stinger key fob Sportage Replacement Key

For many kia sportage keys locked in car models the key comes with a keyless entry system built-in. This key typically resembles an electronic remote and can be changed by a new one purchased from a disassemble kia key fob dealer or locksmith.

Key fobs can stop working due to various reasons, such as an empty coin battery, worn buttons signal interference, water damage, and a defective receiver module. Here are some helpful tips to assist you in getting your Kia sportage replacement key working again.

How do you replace the remote key or smart key?

The battery in your kia picanto smart key's intelligent key will eventually need be replaced, whether it's a remote key as well as a push-to start key or a standard metal key that doesn't contain transponder. This is especially when your car shows a message that states the remote or smart keys aren't powered.

Fortunately, it's quite simple to do. In order to replace the battery in the key fob, remove the mechanical key from the hole in the back of the key fob. Next, pry open the cover. Inside the key fob there will be tiny screws that hold the battery in its place. Utilizing a small screwdriver take the screw off and remove the battery that was in place. Install the new battery and close the opening on the key fob.

Once the key fob has a fresh battery and you've tested it, press the lock and unlock buttons. If the doors unlock and lock according to your expectations, then you're set! You can now use your Kia new key's hands-free lock/unlock feature whenever your fingers feel cold or you need to do some errands in Brandon.

Note: Certain key fobs (transponder chip or smart keys) might require their programming completed. This requires a computer, which is only available to the locksmith who works for the automotive dealer. Other keys (non-transponder metal keys) don't require programming. If you want to change the programming of your key, you'll need record the key code number on the tag for the key code.

How do you replace a battery?

If your Kia key fob isn't responding to pressing the lock or unlock button on the fob, it is a sign that the battery needs to be replaced. A low battery may cause other issues, like the check engine light flashing or the engine not working properly. Fortunately, replacing the battery on the key fob is a fairly simple DIY project that requires just some basic tools.

Before starting the process, make sure that your vehicle is off and that all doors are closed. Find the small metal or a plastic piece at the bottom of the key fob. Press it until the key pops out. You can then insert the key in the driver's door handle to open your car.

To replace the battery on the key fob remove the cover that covers the rear. Use a plastic pry tool to loosen up the latch that holds the black negative cable. Remove the old battery and then orient the new one in a way that the "+" positive side is facing your face and the "negative" negative side is facing towards the fob's metallic electrical contacts. Push the new CR2032 battery straight into place without putting too much force on it to avoid bending or damaging the contacts on the metal.

After the new battery has been installed then turn the key fob off and on in the ignition until the door locks cycle. You can then test your Kia's keys fob once more to ensure it's functioning properly.

How do you replace a smart keys

There is a possibility of having a standard keyfob or a Smart Key based on the model of 2018 kia sportage replacement key Sportage. The smart key features an embedded mechanical key blade unlike the standard key fob, which does not. Both key fobs are equipped with batteries that will eventually require replacing. This is an easy process that takes just two minutes.

Before you begin it is essential to ensure that you're on a flat surface with adequate lighting and that the Kia is off. Keep in mind that the fob can contain tiny pieces that could be thrown off if you're not careful.

The release button for the small size is located on the lower backside. It will be a circular or rectangular slot. You can open the key fob by pressing the button.

Once the key fob is opened, take out the battery. The new battery is a the CR-2032, and it can be bought from a local or online auto parts store. When you're done, the key fob should be able to lock and unlock your vehicle even if it's not running.

How do I replace the mechanical key?

The Kia key fob is a wonderful option that lets us lock and unlock our car with the click of a button. Like any other device like a key fob, the Kia can have issues at times. There are solutions to resolve these issues and keep your key fobs working for the duration of.

A low or dead battery is among the most frequent problems. This can cause your device to stop working or operate intermittently. If this is the case you should replace the battery with a fresh new one.

If this does not solve the issue, you can use an ordinary screwdriver with a flat head to push the plastic casing of the fob open. Be careful not to damage any internal components or scratch the plastic. After the battery has been removed, replace it with a brand new one.

Close and open the door with the mechanical key. (Every kia fob comes with a spare mechanical key that fits into the slot). Test the key fob to ensure it's functioning correctly. If the key fob isn't functioning, contact an expert locksmith or dealer to solve the issue. Make sure they make you an emergency key that can work for all trunk and door cylinders, to avoid future lockouts.