Reasons Your fiat 500 flip key repair 500 Key Fob Won't Work

A key fob from fiat abarth key 500 is a great way to open the doors and start the car. There are many reasons why the key fob might stop working. This could be due to a dead coin battery or water damage, receiver module issues, or interference.

This listing is for an NEW replacement key for fiat ducato van fiat 500 keys Flip Key Remote - an exact replica of the Ilco brand that needs to be programmed professionally by a local automotive locksmith (click here to search for a Locksmith Search). It comes with lock, unlock and trunk buttons.

Dead Coin Battery

The most frequent reason that the 500 key fob won't function is due to an inactive battery. Modern key fobs have a very limited operating range and must be within only a few feet from the vehicle to operate. If you're far from your vehicle, and you hit the keyfob, it won't respond and display the message "Key Fob Not Detected".

If this occurs then replace the battery for your coin-cell (Part Number CR2032) with a new battery from a reputable brand like Panasonic Duracell or Energizer. You can usually find them in your local hardware store, or online.

You can test the battery in the coin-cell by pressing the buttons while standing near your fiat 500 key Fob not working 500. The parking lights should blink and the key fob will operate the lock and unlock switch.

If the fob's key doesn't function after replacing the battery, it may have water damage that prevents it from communicating with the receiver module inside your vehicle. Water damage can happen in a number of ways, ranging from a light splash to submerging your fob in salt water at the beach. If you suspect that your fob was exposed to water, try putting it in a dry rice bag to draw the moisture out. If this doesn't work your fob will probably need to be reset by a professional auto locksmith or by the dealer.

Water Damage

While the fob comes with rubber seals to keep water from the chip's electronic circuit the device, submerging it into the ocean or washing it in a machine can cause water damage. Saltwater can cause the circuit board to short, and eventually cease to function. In the event that you let your fob get wet, it's not a good idea however, if you drop it into an empty cup of water, or do not remember to take it out of your pants pocket prior to running the washer and you don't have a chance, don't give in.

Take the battery off first. Clean the electronic chip using isopropyl or a similar product and dry it completely before replacing the battery. Next try the fob and check if it functions. If the key doesn't function, it may have to be programmed again. This is usually handled by an auto locksmith or dealer.

If the key is a newer model and was not programmed to your vehicle It is likely that it needs to be replaced completely. A professional locksmith for cars can complete this simple process. The locksmith will need the key cut to match the car's ignition. The locksmith will also need to reprogram the fob into the vehicle's system. This is a low-cost and quick process that could be completed the same day.

Receiver Module Issues

One of the main reasons why your 500 key fob won't be working is that it's simply out of range. The remote typically has a range of 30 feet or less, and if it's too far from your vehicle, it will not respond to your commands. This can easily be resolved by moving closer to your vehicle until it starts responding.

If you've replaced your coin battery (commonly known as"button" or "button" or "watch") and your fob doesn't function, it could have an internal circuit board issue. Reprogramming the fob typically resolves this problem. You can find the procedure for the majority of vehicles on YouTube or in the owner's guide.

It is sometimes necessary to replace the clips made of metal that hold the coin batteries in place. If they lose tension, they could stop the battery from being seated properly and could cause your remote to malfunction.

In rare cases the fob can become out of sync with your vehicle because of hardware or software issues. This can be a major headache, but you can frequently fix this issue by visiting an auto locksmith to have them reprogram your fob for you. In certain situations they may have to reinstall the software on your body control module, as well.

Interference

Interference can also cause the key fob not to receive or transmit the signal. This could happen if the key fob is near a radio transmitter (cell phones, radar detectors) or another source of electromagnetic radiation. The key fob might not function due to a poor connection with the buttons or water damage, or damage to the internal chips.

If your key fob suddenly stopped working, or you've tried everything at home to fix it (e.g. It could be a defective 500 receiver module after you've tried replacing the battery, reprogramming, or using a spare key fob. The receiver module is situated under the dash and receives the radio frequency signals from the key fob. It converts the signals into electronic commands that are then read by the vehicle.

There is a simple way to reset the fiat 500 key cover uk's on-board system including the keyfob. Disconnect the battery for 15 minutes by removing first the negative cable and then the positive cable. Then reconnect the battery. This will eliminate any remaining electricity and restart the car's computer system, which can help you the key fob to function again. If the problem persists it is recommended that you consult an expert certified technician. They can determine the exact cause of your issues.