Reasons Your fiat doblo key programming 500 Key Fob Won't Work

A key fob for Fiat 500 allows you to easily open doors and start your car. There are a myriad of reasons the fob could stop working. These include a dead battery, damage to the receiver module, problems, and interference.

This listing is for a NEW replacement fiat punto key programming Flip Key Remote - like the Ilco brand that needs to be professionally programmed by a local locksmith (click here to search for a Locksmith Search). This remote includes lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is the most frequent reason for your 500 key fob being inoperative. Modern key fobs come with a limited range of operation, and should be within a few feet of the vehicle in order to function. If you are far from your vehicle, and you press the keyfob button it won't respond and display the message "Key Fob Not Detected".

If this happens you need to replace the battery of your coin-cell (Part Number CR2032) by a fresh one of a reliable brand, such as Panasonic Duracell or Energizer. You can usually find them in your local hardware store or on the internet.

You can test the coin-cell battery by pressing the buttons while standing near your fiat car key cutting 500 remote key programming (https://historydb.date/) 500. The car will blink its parking lights, and the key fob should work the lock and unlock switches.

If the fob's remote doesn't function after replacing the battery, it might be damaged by water that blocks it from communicating with the receiver module in your car. Water damage can occur in a variety of ways, ranging from small splashes to submerging the fob salt water at the beach. If you suspect that your fob has been exposed to water, try putting it in a dry rice bag to draw the moisture back out. If this fails, you'll have to get your fob replaced by an auto locksmith or dealer.

Water Damage

The fob does have rubber seals to keep water out of the chip's electronic circuit the device, submerging it into the ocean or washing it in a machine can cause water damage. Saltwater is especially dangerous to the circuit board of the fob, causing it to short out and eventually die. It's not a good thing to get the fob wet however, but don't give it up when you accidentally drop it in water, or fail to take it out of your pants pocket.

First, remove the battery from the fob. Before replacing the battery, clean the electronic chip with isopropyl, or a similar product. Next test the fob to test if it works. If the key doesn't work, it might need to be programmed again. This is usually handled by an auto locksmith or dealer.

If the key you have is older and not programmed to work with your vehicle, you will need to replace it completely. This is a straightforward process which can be accomplished by a professional locksmith for automotive use. The locksmith must cut the key to match the ignition of your vehicle. They'll also need to reprogram the fob in the system of your car. This is a cost-effective and quick procedure that can be completed on the same day.

Receiver Module Issues

The 500 key fob could not work because it's out of range. The remote has a maximum range of 30 feet. So when you're too far away from your vehicle it will not respond to your commands. This can easily be resolved by moving it closer to your vehicle until it starts responding.

If your fob won't work after replacing the battery for the coin, also known as a "button", "watch" or "button" It could be due to an issue with the circuit board inside. Reprogramming the fob usually resolves this problem. You can find the instructions for most vehicles on YouTube or in the owner's manual.

It is possible to replace the metal clips that hold the coin batteries in the correct position. If they loose tension it can prevent the battery from sitting properly, and this will result in the malfunction of your remote.

In rare cases it is possible that the fob will become desync'd with your vehicle due to software problems or hardware issues. This issue can be fixed by visiting your local auto-locksmith or dealer to reprogram your key fob. In some instances the software may require reinstallation to your body control modules.

Interference

Interference can also cause the key fob not to receive or transmit a signal. This could occur if the key fob is in close proximity to a radio transmitter, like a cellphone or radar detector. The key fob may not work because of a problem with the buttons, water damage or damage to the internal chips.

If the key fob has failed to work one day in the middle of the night or even after trying everything you can at home to solve it e.g. replacing the battery, reprogramming it and using the spare key fob, you might have a faulty receiver module on your 500. The receiver module is situated under the dash and is able to pick up the radio frequency signals from the key fob. It converts them into electronic commands that the vehicle interprets.

Fortunately, there's an easy method of resetting every single system on board in your 500 device, including the key fob. Disconnect the battery for 15 minutes by removing first the negative cable and then the positive cable. Reconnect the battery. This will get rid of any remaining electrical charge and restart the car's computers. This could help get your key fob working again. If the problem persists you should consult an expert technician. They can diagnose the exact cause of your problem.