Reasons Your fiat 500x key not detected panda key fob replacement (view publisher site) 500 Key Fob Won't Work

A key fob with the fiat 124 spider key fob not working 500 number is a handy way to open the doors and start the car. There are a myriad of reasons why the fob may stop working. It could be due to a dead battery or damage to the receiver module, water issues, and interference.

This listing is for an NEW replacement fiat panda key programming Flip Key Remote that appears similar to the Ilco brand. It needs to be professionally programmed (click here to search for local automotive locksmiths). Includes trunk, lock and unlock buttons.

Dead Coin Battery

The most frequent reason that your 500 key fob won't function is the battery is dead. Modern key fobs have a very limited range of operation, and must be within just a few feet of the vehicle to function. If you're far from your vehicle and you hit the keyfob, it will not respond and display the message "Key Fob Not Detected".

If this happens, replace the battery on your coin cell (Part number CR2032) with a new one from a reliable brand such as Panasonic, Duracell, or Energizer. You can typically find them at your local hardware store, or online.

You can test the coin-cell battery by pressing the buttons while you are standing close to your fiat doblo key programming 500. The car will blink its parking lights, and the key fob should work the lock and unlock switches.

If the fob's remote doesn't work after replacing the battery, it might have water damage that prevents it from communicating with the receiver module in your vehicle. Water damage can happen in a number of ways, from the slightest splash to submerging the fob salt water at the beach. If you suspect that your fob was exposed to water, put it in a rice bag to draw out the moisture. If this does not work, you'll need to have your fob changed by an auto locksmith or a dealer.

Water Damage

Although the fob is equipped with rubber seals that keep water from the electronic chip inside it, submerging it in the ocean or washing it in a machine could cause water damage. Saltwater can cause the circuit board to short and eventually fail. It's not the best idea to soak the fob in water however, but don't give it up when you accidentally drop it in water or forget to remove it from your pocket.

First take the battery off the fob. Clean the electronic chip using isopropyl alcohol or another similar product and then dry it thoroughly before replacing the battery. Then check the fob to test if it works. If the key doesn't work, it might need to be reprogrammed. This is usually handled by an auto locksmith or dealer.

If the key is older and has not been programmed to your car it is likely to need to be replaced completely. A professional locksmith for automotive can complete this simple process. The locksmith must cut the key to match the ignition of your vehicle. The locksmith will also have to reprogram your fob in the fiat punto car key replacement's system. This is a quick and cost-effective procedure that can be completed in the same day.

Receiver Module Issues

One of the most common reasons why your 500 key fob might stop functioning is that it's out of range. The remote typically has a range of 30 feet or less, and if it's too far away from your car it will not respond to your commands. It's easy to remedy this by moving your remote closer to your vehicle until it responds.

If your fob doesn't work after replacing the battery for the coin, also called a "button", "watch" or "button" It could be a problem with the circuit board inside. In the majority of cases, reprogramming your fob can resolve the issue. You can find instructions on how to do this for all automobiles by searching YouTube or reading the owner's manual.

It is possible to replace the metal clips that hold the coin batteries in their place. If they loose tension they could stop the coin battery from being seated properly and cause the remote to malfunction.

In rare cases, the fob may become disconnected from your vehicle due to software or hardware issues. This issue can be fixed by visiting your local dealer or auto-locksmith to reprogram your key fob. In certain instances the software might need to be reinstalled in your body control modules.

Interference

In addition to a dead coin battery The key fob might not be receiving or transmitting an signal due to interference. This is possible when the key fob is near a radio transmitter (cell phones and radar detectors) or another source of electromagnetic radiation. Other reasons the key fob may not function could be due to a weak connection to the buttons, damage to the internal chip or water damage.

If your key fob suddenly stopped working, or if you've tried everything at home to solve the issue (e.g. It could be a defective 500 receiver module if you've tried replacing the battery, reprogramming it, or using an alternative key fob. The receiver module is located under the dash and is able to pick up the radio frequency signals from the key fob. It then converts them into electronic commands that the vehicle interprets.

Luckily, there is an easy way to reset all of the onboard systems in your 500, including the key fob. Disconnect the battery 12 volt for about 15 minutes, by removing the negative cable and then the positive cable. Reconnect the battery. This will eliminate any remaining electricity, and restart the car's computer. This will help you get your key fob to work again. If the issue persists, you should consult a certified technician. They will be able to identify the root cause of your issue.