UPVC Window Repairs

Upvc windows are energy efficient and help to reduce heating bills. As they get older, however, issues can occur that need to be addressed. This can be due to damaged handles, hinges, or locks.

Wooden window repair is relatively straightforward for DIY enthusiasts to complete themselves. It can also be cheaper than buying a new window.

Cracks

Cracks and fractures in uPVC windows can be a serious problem. Leaving them unrepaired can lead to water ingress and less effective barriers against cold weather and even the possibility of structural damage. Find a local builder who is skilled in the repair of uPVC frames. They must possess the necessary knowledge and experience, as well as the equipment needed to ensure the best results. This will ensure that your shattered window is repaired before it gets any worse and you don't have to replace the window glass or window repairs near me unit.

Small cracks in glass can be fixed by using a variety of home-based solutions. Masking tape and super glue are among the most common products that can hold broken glass in place for a time. For deeper cracks, tape may need be extended on both sides.

You can also make use of two-part epoxy for repairing damaged or cracked glasses. Most hardware stores offer this product at around $10. Make sure your work area is properly prepared prior to mixing the epoxy. Also, ensure you have all the equipment required for the job.

If your lower or upper sash is difficult to raise it's most likely due to the fact that the cords on the sash weights are damaged. It's an easy fix that can be accomplished with the help of the ladder and a flathead screwdriver. Replacing a rotted drip cap is a different repair that is done at home. Many home centers stock a drip caps that are not rot free and can be easily caulked or nailed in place. Also, if you have a double glazed window repairs- or triple-paned window, be sure to make sure that one of the panes are not broken. This is because the gases that are filling the space between the panes contribute to improving energy efficiency and should be retained, not escaping.

Water Leaks

If your uPVC window is leaking, it could ruin your interior and result in costly repairs. Water leaks may also cause structural damage to your home, as well as mold growth. It is crucial to address any issues caused by leaky windows right away to minimize damage.

One common cause of window leaks is a damaged sealant around the frame. Using silicone caulking can help bring the condition of the seal back to normal and prevent water leakage. Check for cracks and gaps between the window frame as well as the brick or stone wall surrounding your windows.

A blocked drainage hole or an issue with flashing are the other two typical causes of windows leaking. It's crucial to make sure the drainage holes are free and unclogged, especially during heavy rainstorms. You should also look at the window's flashing to ensure that it is well-sealed.

Lastly, it's important to check that your drip cap isn't missing or damaged. A damaged or damaged drip cap can allow water to enter the window from above, causing damage to your home's structure. Replacing a drip cap isn't an arduous task and is usually a straightforward process of purchasing an entirely new one and nailing it into the correct position.

A professional can also examine your windows for watertightness. They can employ a tool to measure the water-tightness of your windows, and make sure they are in compliance with the standards of the industry. If your windows don't pass the test, you'll have to replace them. This is a costly repair, but it's worth it for the comfort and security of your family.

Sagging

If your windows don't close properly, it can lead to a number issues including drafts, condensation and a rise in your energy bills. It could also mean that the windows were not installed correctly or that the sealant has worn out. Fortunately, there are some things you can do to fix the issue.

The first step is to prepare a workspace in a room that has plenty of light to repair your window properly. Begin by placing newspaper or an old blanket on the floor to shield it from any splinters or drips that might be coming from the window as you work.

Use a white cloth soaked in a mixture of water and detergent. This will ensure that you don't leave any color stains on your windows. If you're ready to begin working on your uPVC windows, start by making a note of the location where the hinge channel needs to be situated. Unscrew the channel, and then fill the screw holes in the frame with epoxy (for uPVC frames) or wood filler. Make sure you scrape the hole you have filled before it sets.

Once the holes have been filled, you can put in the hinge channel. Make sure that it is aligned with the window jamb, and that you drill the holes for the new screws about a quarter inch from the original locations.

Then, take a measurement of the length of the spindle protruding from underside of the handle and order an alternative online or bring the old one to a hardware store for matching. Then, pull out the setscrew that was on the operator shaft and file it flat so the set screw can be secured to the shaft (photo). Then, your uPVC windows should shut without a hitch.

Broken Hinges

If your uPVC window hinges have been damaged or are not functioning correctly and you are unable to open or close the window, it will be difficult to open or close the window. This can be a security problem and could also hinder your home from staying warm or cold. It's easy to get a new window hinge for your uPVC windows. It's essential to make sure you have the right hinge for your windows.

The hinges need to be identical in size to fit inside the window frame. The most common type of hinge used in uPVC windows is a standard 18mm or 15mm UPVC window hinge. However, there are special kinds of window hinges that are suitable for different kinds of frames such as wooden frames. Getting the correct type of window hinge for your windows will aid in avoiding common problems that many homeowners have with their windows, like not closing properly.

There are many reasons why the hinges on your windows have become slack or stiff. The hinges may not be sufficiently tightened. To test this, take a screwdriver and locate the friction screw on the hinge's end. Release it. You can then adjust it by turning it either way.

If your UPVC window hinges are not functioning as they should, contact Preston Glass Fix for a quick repair. Our technicians will evaluate the condition of your hinges for your windows and provide you with the best solution for you. We can replace window hinges or retension them, or even install new lock mechanisms to ensure your UPVC windows are secure and safe.

Locks that aren't working

UPVC window locks and mechanism are an essential component of home security. they make it very difficult to open the window without breaking. If a lock fails, it can be frustrating, but it is a quick and easy repair and you don't have to replace the entire window.

Sometimes, the issue is a small issue which could have been averted by regular maintenance. We suggest having your uPVC window maintained regularly as part of our annual maintenance package in order to minimize the chance of any issues.

Modern uPVC windows come with espagnolette locks. These work by pushing the nose end of the handle on the block with a wedge, and then turning it to close the lock. They are efficient in locking the window, however if they are not maintained properly, over time they can begin to fail. We recommend applying WD-40 to them a few times a year.

If you find that your uPVC window isn't opening and closing as quickly as it used to or when the lock isn't working correctly, it could be an issue with the locking gearboxes within the frame. Accessing this can be tricky because it requires the removal of the seals that surround the frame as well as the removal of the handle (be careful not to damage these).

A locksmith who is skilled in UPVC repair will be able to detect the issue quickly and replace the failed locking mechanism with a precise replacement. This is a fast and easy repair that can save you hundreds of dollars by avoiding the need to buy new windows.